Mika Specialty Grinding Bits for mirror edges, beveling and jewelry work

Very high quality, long lasting specialty grinding bits from Mika International that will fit Inland, Diamond Tech, Gryphon and Glastar grinders.

When regular bits aren't quite enough, these beveling, mirror edge, and jewelry bits will do the job. Made in Germany.

Mika Mirror Grinding Bit, Fine Grit, 3/4"

Item no: 7062A

Mika International item: ME-6F

Retail price: $52.80

In stock: 0

No longer available.

Click to view or buy this item

The perfect choice for those times when you need a perfectly smooth chip-free edge that won’t be covered over by copper foil tape or lead came. In addition to mirror edging, use this bit for mosaic pieces, wind chimes, or textured glass that is hard to foil. Simply position the bit so that your glass will pass through the groove in the bit. The profile of the bit will slightly taper the back and front side of your glass piece and the fine grit of the head will leave a soft frosted, smooth, chip-free edge.

Mika Jewelry Grinding Bit

Item no: 7062P

Mika International item: ME-10S

Retail price: $52.80

In stock: 0

No longer available.

Click to view or buy this item

The thin diamond coated disc grinds a small groove in the edge of your fused jewelry pieces that will hold your your wire securely in place without the need to do time consuming decorative wire wraps. 5/8" diameter with standard grit, the thin, disc-like grinding surface is less than 1/16" thick. This bit is designed to work in tight places and at acute angles on glass jewelry pieces. The grit begins approximately 1/16" over the top of the disc, and wraps around it at an equal distance on the bottom. The disc is situated at the bottom of the spindle for use as an alternate method of wire wrapping fused jewelry pieces. The thin diamond coated disc grinds a small groove in the edge of your fused jewelry pieces that will hold your your wire securely in place without the need to do time consuming decorative wire wraps.

Mika 45 Degree Mitering Bit (1-3/8")

Item no: 7062L

Mika International item: ME-9S

Retail price: $108.00

3 or more $97.20 (10% discount)
6 or more $86.40 (20% discount)

In stock: 1

Click to view or buy this item

Standard grit. Designed to give a consistent mitered edge to glass. It is perfect for three-dimensional assemblies and boxes. The 1-3/8" dimension is the outer limit of the flanged portion. The main section of the bit is 3/4" diameter. The beveled surface is 7/16" wide. Leaves a perfect 45 degree mitered edge on your glass pieces to help you create perfect boxes, cardholders, miniature houses, terrariums and other 3-D projects, all without the expense of a disc grinder!

Mika 1-1/2" Super Fine Grit Beveling Bit

Item no: 7062R

Mika International item: ME-11SFT

Retail price: $72.00

3 or more $64.80 (10% discount)
6 or more $57.60 (20% discount)

In stock: 1

Click to view or buy this item

A 1-1/2" diameter bit that will fit all grinders that will accept 3/4" or 1" bits. The bit puts a 7 degree beveled edge on your glass, leaving a highly frosted finish. It has a standard 3/4" diameter with a 1-1/2" diamond angled surface for precision beveling. Create a custom frosted bevel within minutes. Inside curves, outside curves and straight lines - all are no problem with these bits. The key is all in the design of these bits that will have you beveling your glass or creating decorative edging like an expert within minutes on your standard grinder. No lengthy learning curve and no expensive equipment. The ME-11SF creates a 1/2" wide 7 degree bevel.